White Knight Rust Guard® Touch Up

300g Aerosol can

White Knight Touch Up is an acrylic formulation designed for the repair and maintenance of pre-painted metal.



Features

• Touch Dry in 15 minutes*

• Available in satin finishes to match COLORBOND®** and powder coated metal surfaces (only satin not Gloss)

• Hard wearing

• Excellent coverage and adhesion

• Adjustable spray nozzle

• Safe to spray - CFC and lead free

• Non-chroming formula

* At an average temperature of 25oC, relative humidity 50%

**COLORBOND® is a registered trademark of BlueScope Limited

Touch Up is suitable on ferrous metals (steel and wrought iron), non-ferrous metals (aluminium and brass) and pre-painted metal (COLORBOND®*).

*COLORBOND® is a registered trademark of BlueScope Limited

 

1. PREPARATION

AEROSOL:

  • Remove all stains and marks with a metal polish and wash surface with White Knight Rust Guar® Solvent or mineral turps.
  • The surface must be clean, dry and free from dust, dirt, grease oil, rust scale and other contaminants.
  • Do not handle surface prior to applying White Knight Rust Guard Clear Guard.
  • Cover surrounding areas to protect from overspray.

BRUSH ON:

  • Remove all stains and marks with a metal polish and wash surface with White Knight Rust Guard Solvent or mineral turps.
  • The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants.
  • Do not handle surface prior to applying White Knight Rust Guard Clear Guard.

2. APPLICATION

  • The surface must be thoroughly clean, dry and free from grease, oil, dirt, rust scale and other contaminants.
  • Thoroughly sand previously painted or glossy surfaces with 600# wet n dry abrasive paper.
  • Cover all necessary surrounding areas to protect from overspray.

BEFORE SPRAYING

  • Shake can vigorously for 1 minute to ensure colour uniformity. Shake can occasionally during use.
  • Test spray on a small inconspicuous area to ensure surface compatibility and finish suitability.

SPRAYING 

  • Select the nozzle setting: The horizontal setting should be used when spraying up and down and the vertical setting should be used when spraying across. To change the nozzle setting, turn the red section on the nozzle.
  • Hold the can upright approximately 15-20cm from the surface.
  • Press button firmly and spray several light coats with a smooth sweeping motion, overlapping each spray pass. To prevent paint from sagging, avoid spraying too close to the surface or applying a heavy coat.
  • Repeat if necessary.

NOTE: Weathering will affect White Knight Touch Up Paint and pre-painted metal differently. Therefore, some difference in appearance may result over time.

Do not use when air or surface temperature is below 15°C or above 30°C or in excessive humidity. 

3. COVERAGE

Approximately 1.5m² per can.

4. DRYING

  • Touch dry 15 minutes. Re-coat after 1 hour.
  • Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.

5. CLEAN UP

  • Overspray can be removed while still wet with White Knight Rust Guard Solvent or mineral turps.
  • To clean the nozzle after use and prevent blocking turn the can upside down and press button until only gas escapes.

6. SAFETY & FIRST AID

KEEP OUT OF REACH OF CHILDREN.

  • If swallowed, seek medical advice immediately and show the container or label. Do not induce vomiting.
  • If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention.
  • Avoid breathing vapour or mist.
  • Use only with adequate ventilation.
  • If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners.
  • Warning - Misuse by concentrating and inhaling contents can be harmful or fatal.

For 24 hour medical emergency response service in Australia call 1800 883 254 and in New Zealand call 0800 000 096

7. CAUTION

EXTREMELY FLAMMABLE. Keep can away from flame and heat and eliminate any source of ignition. Keep can in a cool place and out of sun. Contents of can under pressure. Do not puncture or incinerate the can, even when empty.

8. ENVIRONMENT

  • Residual paint should be sprayed onto newspaper, allowed to dry and then disposed of via domestic waste collections.
  • Empty aerosol cans are recyclable via steel can recycling programs.

Colour Range

The following White Knight Touch Up colours match Colorbond® colours and satin finishes.

Colorbond Off White (Surfmist)
Colorbond Smooth Cream (Classic Cream)
Colorbond Merino (Paperbark)
Colorbond Sandbank
Colorbond Evening Haze
Colorbond Wheat (Harvest)
Beige
Colorbond Shale Grey
Colorbond Dune
Colorbond Mist Green (Pale Eucalypt)
Colorbond Rivergum (Wilderness)
Colorbond Caulfield Green (Cottage Green)
Colorbond Tuscan Red (Headland)
Colorbond Heritage Red (Manor Red)
Colorbond Mountain Blue (Deep Ocean)
Colorbond Slate Grey (Woodland Grey)
Colorbond Ironstone
Colorbond Jasper
Colorbond Loft
Colorbond Monument
Satin Black
Colorbond Cove
Mangrove
Basalt
Gully
Wallaby
Terrain
*Due to colour variations in all browser types, the displayed colour palettes are a representation only of the actual colour. This should not be used in deciding the colour range suitable for you application.

Need Help?

It’s as easy as selecting a project type and the material involved