White Knight Ultra Pave® Heavy Duty

1L, 4L, 10L

White Knight Ultra Pave® Heavy Duty is a tough, hard wearing formulation with built in DuraTough® technology. The semi-gloss finish resists scuffing and marking and is the perfect solution for refreshing tired concrete areas.



Features

• Resists scuffing and marking

• Resists hot tyre pick up

• No primer required

• Excellent adhesion to concrete

• Suitable for bare and previously painted concrete surfaces

• May be applied over oil and water based topcoats

• Semi gloss finish

• Tintable bases – White, Accent, Medium Grey

• Tintable to a great range colours

• Product achieves minimum of an P3 slip rating when applied as directed, as tested to AS/NZS 4586-2013 Appendix A.

White Knight Ultra Pave® Heavy Duty is ideal for garage floors, carports, and other flat surfaces where
you may park your car. Not recommended for sloped surfaces.

Use of the White Knight Ultra Pave Topcoat Grip additive is strongly recommended for improved slip resistance in areas that may become slippery when wet.

1. PREPARATION

  • To obtain best results the surface must be prepared correctly before application:
  • Allow new concrete to cure for 12 weeks before painting.
  • Repair or replace unsound concrete.
  • The surface must be clean and free from dust, dirt, grease, oil, moss, loose material and other contaminants.
  • Remove any previously applied sealant or curing compound by mechanical sanding or grinding.
  • Remove any loose concrete by scraping, grinding, high pressure water blasting, wire brushing or sanding.
  • Clean the surface with a strong detergent and hose off with clean water.

2. SMOOTH CONCRETE & GARAGE FLOORS (new, old or bare)

  • Etch surface with Ultra Pave Concrete Etcher following label directions.
  • After etching, scrub surface thoroughly with a stiff bristle broom and pressure hose with clean water to remove all loose material and residue.
  • Check that the surface has roughened. If it doesn’t feel like 180# sandpaper repeat the etching process.
  • Test for loose residue with adhesive tape. If loose material is picked up on the tape, repeat the cleaning process.
  • Allow concrete to dry completely.

3. ROUGH CONCRETE (new or old, bare)

  • Scrub the surface with a stiff bristle broom to remove any loose residue then rinse thoroughly with a strong water jet (eg garden or pressure hose).
  • Test for loose residue with adhesive tape. If loose material is picked up on the tape repeat the cleaning process.
  • Allow concrete to dry completely.

4. PREVIOUSLY PAINTED CONCRETE

  • Check for lifting of old paint. If it is not sound, remove all old paint.
  • Scrape off all loose and flaking paint by wire brushing or sanding.
  • Sand glossy or smooth surfaces thoroughly.
  • Rinse surface thoroughly with clean water.
  • Allow concrete to dry completely.
  • Test paint on a small inconspicuous area to ensure compatibility with the old coating. After 24 hours of drying, check for lifting of old paint or poor adhesion. If problems are observed total removal of the old paint is required.

5. APPLICATION

  • Stir thoroughly with a broad, flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
  • Apply 2 coats by brush or roller. Thin the first coat on bare concrete with 10% turps to aid penetration and adhesion. For added slip resistance add Ultra Pave Topcoat Grip Additive to the second coat following label directions.

DO NOT USE AT TEMPERATURES BELOW 10°C OR ABOVE 30°C

6. COVERAGE

Approximately 14m² per litre, depending on the porosity of the surface.

7. DRYING

Touch dry in 1 hour. Re-coat after 16 hours. Light traffic after 4 days. Heavy traffic after 7 days. Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.

8. CLEAN UP

Clean brushes and equipment with mineral turps immediately after use.

9. CARE & MAINTENANCE

Wash as often as required with water and mild detergent. Do not use harsh abrasive brushes or high-pressure water hoses. Long exposure to pooling water or chemicals will damage the paint and they should be removed or cleaned quickly.

10. SAFETY & FIRST AID

  • KEEP OUT OF REACH OF CHILDREN.
  • This product is flammable. Keep away from heat and eliminate any source of ignition.
  • If swallowed, seek medical advice immediately.
  • Do not induce vomiting.
  • If in eyes, flush with cold water. Seek medical advice immediately.
  • If on skin wash with soap and water or recognised skin cleanser. Do not use solvents or thinners.
  • May be harmful if inhaled. Avoid inhalation of vapour. Remove to fresh air if affected.
  • Ensure adequate ventilation during use and while drying.

For 24 hour medical emergency response in Australia call 1800 883 254 and in New Zealand call 0800 000 096

11. ENVIRONMENT

  • Do not pour unwanted paint down the drain.
  • Keep unwanted paint in sealed containers for disposal via chemical waste collections.
  • Empty paint containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via steel recycling programs.
  • Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your council first.

Colour Range

The Ultra Pave® product range can be tinted to the following colours.

Colorbond - Dune
Colorbond - Paperbark
Colorbond - Woodland Grey
Colorbond - Pale Terracotta
Colorbond - Windspray
Colorbond - Stone
Colorbond - Classic Cream
Colorbond - Shale Grey
Colorbond - Wheat
Colorbond - Surfmist
Colorbond - Sandbank
Crazy Grey
Crocs Cavern
Crush
Crystal Crush
Cuttle Fish
Dark Desert
Deep Moss
Diamond Delight
Blue Wedge
Fresco
Granite Frost
Jade Juice
Lobster Lush
Mighty Mink
Mystic Storm
Oceanic
Opal Glow
Panhandle Grey
Oyster Shell
Bubble
Primal Pink
Raging Sea
Ravish
Rock Pool
Rita Stone
Rivers End
Sister Moon
Caustic Cream
Smoke Storm
Sorbet
Stonewash
Storm Grey
Summer Rain
Sunset Waters
Sweet Fudge
Tangled Straw
Thunder Storm
Caves Beach
Clusters
Cool Copper
Sand Dune
Mint Stick
Beige PT
Icy Bay
Forest Shadow
Clear Atrium
Blue Button
Shindig
Winter Mist
Cold Steel
Grey Frost
Sealord
Raven Feather
Smokey Mood
Lunar Eclipse
Cannon Ball
Thin Ice
Secret Passage
Struan Grey
Whitehouse
Gazebo White
Barely Beige
Eagle Crest
Spider Web
Canyon Trail
Silver Spoon
Grey Marble
Platonic
Gibraltar Grey
Grey Ghost
Silver Dollar
Beige Ash
Asian Timber
Tightrope
Milk Cloud
Augustus
Dune Grass
Leather Beige
Navajo Beige
Classic Khaki
Stony Creek
Saddle Soap
Mountain Grey
Toasted Almond
Dusty Trail
Witchwood
Vintage Lace
Cream Curd
Heavy Cream
Vanilla Brandy
*The displayed colours are a representation only, and may not reflect actual colour upon application. Due to colour variations between browser and display types this palette should be used as a guide only when choosing the colour for your project. ® colour names are registered trade marks of BlueScope Steel Limited. TM colour names are trade marks of BlueScope Steel Limited.

Need Help?

It’s as easy as selecting a project type and the material involved