Glow Safe

White Knight Glow Safe may be used on rendered surfaces, timber, concrete, bitumen, ceilings, previously painted surfaces, metal pipes and tubes, plasterboard.

• KEEP OUT OF REACH OF CHILDREN.
• This product is highly flammable. Store and use away from heat and eliminate any source of ignition.
• Soak any clothes used in water immediately after use as they may self ignite.
• If swallowed, seek medical advice immediately and show the container or label. Do not induce vomiting.
• If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention.
• Avoid breathing vapour or mist.
• Use only with adequate ventilation.
• If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners.
• Warning - Misuse by concentrating and inhaling contents can be harmful or fatal.

For 24 hour medical emergency response in Australia call 1800 807 001 and in New Zealand call 0800 154 666

HIGHLY FLAMMABLE. Keep can away from flame and heat and eliminate any source of ignition. Keep can in a cool place and out of sun. Contents of can under pressure. Do not puncture or incinerate the can, even when empty.

AEROSOL:

• Residual paint should be sprayed onto newspaper, allowed to dry and then disposed of via domestic waste collections.
• Empty aerosol cans are recyclable via steel can recycling programs.
• Important: Deliberate misuse of this product to damage public or private property is a crime.

BRUSH ON:

• Do not pour unwanted paint down the drain. Keep unwanted paint in sealed containers for disposal via special chemical waste collections.
• Empty paint containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via can recycling programs.
• Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first.

• Thoroughly clean the surface and ensure it is dry and free from grease, oil, dirt, rust scale and other contaminants.
• Remove all loose rust and flaking paint.
• Thoroughly sand glossy or enamel surfaces.
• Fill nail holes and cracks with appropriate filler and sand smooth.
• Treat any mould with suitable anti-mould solution.
• May be applied over any background colour, however a white background will provide the brightest glow.

Bare concrete:

• Prepare surface as detailed above. Apply one coat of White Knight Ultra Pave White as per label directions.

Previously painted surfaces:

• Prepare surface as detailed above. Apply one coat of Taubmans 3-in-1 Primer Sealer Undercoat as per label directions.

Bare steel and wrought iron:

• Prepare surface as detailed above.  Prime with White Knight Rust Guard All Purpose Primer or White Knight Rust Guard Metal Primer as per label directions.

Galvanised iron and non ferrous metal (e.g. aluminium, copper, brass):

• Prepare surface as detailed above. Prime with White Knight Rust Guard SLS Etch Primer as per label directions.

Timber:

• Prepare surface as detailed above. Prime with White Knight Rust Guard All Purpose Primer or Taubmans 3-in-1 Primer Sealer Undercoat as per label directions.
• For other surfaces use an appropriate primer undercoat.
• Cover all necessary areas to protect from overspray.

AEROSOL

BEFORE SPRAYING

1. Shake can vigorously for 1 minute to ensure colour uniformity. Shake can occasionally during use.
2. Remove the cap carefully. Avoid using sharp objects that may puncture the can.

SPRAYING

1. Select the nozzle setting: The horizontal setting should be used when spraying up and down and the vertical setting should be used when spraying across. To change the nozzle setting, turn the red section on the nozzle.
2. Hold the can upright approximately 25cm from the surface.
3. Press button firmly and spray several light coats with a smooth sweeping motion, overlapping each spray pass. To prevent paint from sagging, avoid spraying too close to the surface or applying a heavy coat.
4. Repeat if necessary.

BRUSH ON

1. Stir thoroughly with a broad flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
2. Apply 1-3 coats by brush or roller, depending on glow time required.

Do not use when air or surface temperature is below 15°C or above 30°C or in excessive humidity.

Aerosol: Approximately 1.5m² per can, depending on the nature of the surface and amount of overspray.

Brush on: Approximately 8m² per litre, depending on the nature of the surface.

Aerosol: Touch dry in 15 minutes. Re-coat after 1 hour.
Brush on:  Touch dry in 30 minutes. Re-coat after 2 hours.

Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.

Brightness and glow time is dependant on the film thickness applied, the ambient light level and the duration of exposure to light. Brighter lights and longer exposure will result in a brighter/longer glow time.

For heavy traffic areas, White Knight Glow Safe may be over-coated with White Knight Clear Guard to extend the life of the painted surface.

Aerosol: Overspray can be removed while still wet with White Knight Rust Guard Solvent.

To clean the nozzle after use and prevent blocking turn the can upside down and press button until only gas escapes.

Brush on: Clean brushes and equipment with water immediately after use.