Hammered Finish

White Knight Rust Guard Hammered Finish may be used on all metal surfaces.

AEROSOL:

• KEEP OUT OF REACH OF CHILDREN.
• If swallowed do not induce vomiting. Drink a glass of water and seek medical advice.
• If in eyes, immediately flush out with water and seek medical advice.
• Avoid breathing vapour.
• Ensure adequate ventillation during use and while drying.
• If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Seek medical advice if irritation persists.
• Warning - Misuse by concentrating and inhaling contents can be harmful or fatal.

BRUSH ON:

• KEEP OUT OF REACH OF CHILDREN.
• This product is flammable. Keep away from heat and eliminate any source of ignition.
• If swallowed do not induce vomiting. Drink a glass of water and seek medical advice.
• If in eyes, flush out immediately with water and seek medical advice.
• Avoid prolonged breathing of vapour.
• Ensure adequate ventillation during use and while drying.
• If on skin, remove contaminated clothing and wash skin thoroughly with soap and water. Seek medical advice if irritation persists.

For 24 hour medical emergency response in Australia call 1800 807 001 and in New Zealand call 0800 154 666

HIGHLY FLAMMABLE. KEEP AWAY FROM FLAME AND ELIMINATE ANY SOURCE OF IGNITION. Keep in a cool place and out of sun. Contents under pressure. Do not puncture or incinerate this can, even when empty.

AEROSOL:

• Residual paint should be sprayed onto newspaper, allowed to dry and disposed of via domestic waste collections.
• Empty aerosol cans are recyclable via steel can recycling programs.

BRUSH ON:

• Do not pour unwanted paint down the drain.
• Keep unwanted paint in sealed containers for disposal via chemical waste collections.
• Empty paint containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via steel recycling programs.
• Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first.

AEROSOL:

• Remove all rust and loose and flaking paint.
• Sand new metal, previously painted or glossy surfaces thoroughly.
• The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants.
• Convert rusted steel and wrought iron surfaces with White Knight Rust Guard Rust Converter.
• Prime rusted steel and wrought iron with White Knight Rust Guard Metal Primer.
• Prime galvanised iron, ZINCALUME® and non ferrous metals e.g. aluminium with White Knight Rust Guard True Bite or SLS Etch Primer.
• In highly corrosive conditions such as coastal areas prime steel and wrought iron with White Knight Rust Guard Metal Primer.
• Cover surrounding areas to protect from overspray.

BRUSH ON:

• Remove all rust and flaking paint.
• Sand new metal, previously painted or glossy surfaces thoroughly.
• Convert rusted surfaces with Rust Guard Rust Converter.
• The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants.
• Prime galvanised iron, ZINCALUME® and non ferrous metals e.g aluminium with Rust Guard True Bite or SLS Etch Primer.
• In severe conditions, or for added protection to steel and wrought iron, prime with Rust Guard Metal Primer.

AEROSOL:

1. Shake can vigorously for 1 minute before use and regularly during use.
2. Adjust nozzle to desired spray pattern. Use the horizontal setting when spraying up and down and the vertical setting when spraying across.
3. Hold the can upright approximately 15-20 cm from the surface.
4. Press button firmly and spray with a smooth sweeping motion. Apply a pre-wetting mist coat followed by a full even coat, overlapping each spray pass. To prevent paint sagging, avoid spraying too close to the surface or spraying too heavily.
5. Repeat if necessary.

Do not use when air or surface temperature is below 15°C or above 30°C

BRUSH ON:

1. Stir thoroughly with a broad flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
2. Apply 2 coats by brush, roller or spray gun.

Do not use when air or surface temperature is below 10°C or above 30°C

AEROSOL: Approximately 2m² per can.

BRUSH ON: Approximately 10m² per litre, depending on the nature of the surface.

AEROSOL:  Touch dry in 30 minutes. Re-coat exactly after 1 hour or after 2 days. Do not re-coat between 1 hour and 48 hours after initial application.

BRUSH ON: Touch dry in 4-6 hours. Re-coat after 24 hours.

Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.

AEROSOL: To prevent nozzle blocking, after use turn can upside down and press button until only gas escapes.

Overspray can be removed while still wet with White Knight Rust Guard Solvent or mineral turps.

BRUSH ON: Clean brushes and equipment with White Knight Rust Guard Solvent or mineral turps immediately after use.