Epoxy Enamel

White Knight Rust Guard Epoxy Enamel may be used on all metal surfaces.

• KEEP OUT OF REACH OF CHILDREN.
• This product is highly flammable. Store and use away from heat and eliminate any source of ignition.
• Soak any clothes used in water immediately after use as they may self ignite.
• If swallowed, seek medical advice immediately and show the container or label. Do not induce vomiting.
• If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention.
• Avoid breathing vapour or mist.
• Use only with adequate ventilation.
• If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners.
• Warning - Misuse by concentrating and inhaling contents can be harmful or fatal.
• For 24 hour medical emergency response in Australia call 1800 807 001 and in New Zealand call 0800 154 666

EXTREMELY FLAMMABLE. KEEP AWAY FROM FLAME AND ELIMINATE ANY SOURCE OF IGNITION. Keep in a cool place and out of sun. Contents under pressure. Do not puncture or incinerate this can, even when empty.

1. Do not pour unwanted paint down the drain.
2. Keep unwanted paint in sealed containers for disposal via special chemical waste collections.
3. Residual aerosol paint should be sprayed onto newspaper, allowed to dry and disposed of via domestic waste collections.
4. Empty paint containers should be left open in a well ventilated area to dry out. When dry, recycle steel containers via can recycling programs.
5. Empty aerosol cans are recyclable via steel can recycling programs.
6. Disposal of empty paint containers via domestic recycling programs may differ between local authorities. Check with your local council first.

White Knight guarantees that White Knight Rust Guard Epoxy Enamel will inhibit the development of rust for 5 years provided

a) it is applied following White Knight instructions and

b) the appropriate and necessary White Knight Preparation and Primer products are applied prior (if required) following White Knight instructions. This guarantee is given by the manufacturer and applies to defects in the manufacture or formulation of the White Knight Rust Guard Epoxy Enamel. Blistering, peeling and flaking are not covered under this guarantee. Any damage to the coating incurred after using the White Knight Rust Guard system must be repaired immediately to inhibit rust development.

This guarantee does not cover application in highly corrosive areas or paint failure caused by any breakdown of coatings applied previously or use of other coating not specified by White Knight or any factors beyond the control of the manufacturer. The guarantee is only applicable for domestic use. White Knight's liability under this Guarantee is limited to replacing the paint or the cost of replacing the paint to rectify the affected areas. White Knight is not liable for the cost of any labour or any other direct or indirect loss or damage arising from a breach of this Guarantee. Nothing set out above excludes or restricts your statutory rights.

1. Remove all rust and loose and flaking paint.
2. Sand new metal, previously painted or glossy surfaces thoroughly.
3. The surface must be clean, dry and free from dust, dirt, grease, oil, rust scale and other contaminants.
4. Convert rusted steel and wrought iron surfaces with White Knight Rust Guard Rust Converter.
5. Prime rusted steel and wrought iron with White Knight Rust Guard Metal Primer.
6. Prime galvanised iron, ZINCALUME® and non ferrous metals e.g. aluminium with White Knight Rust Guard True Bite or SLS Etch Primer.
7. In highly corrosive conditions such as coastal areas prime steel and wrought iron with White Knight Rust Guard Metal Primer.
8. Cover surrounding areas to protect from overspray.

AEROSOL:

1. Shake can vigorously for 2 minutes before use and regularly during use.
2. Adjust nozzle to desired spray pattern. Use the horizontal setting when spraying up and down and the vertical setting when spraying across.
3. Hold the can upright approximately 15-20 cm from the surface.
4. Press button firmly and spray with a smooth sweeping motion. Apply a pre-wetting mist coat followed by a full even coat, overlapping each spray pass. To prevent paint sagging, avoid spraying too close to the surface or spraying too heavily.
5. Repeat if necessary.

Do not use when air or surface temperature is below 15°C or above 30°C

BRUSH ON:

1. Stir thoroughly with a broad flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
2. No thinning is required for application by brush or roller. If spraying you may thin up to 10% with White Knight Rust Guard Solvent.
3. Apply 2 coats by brush, roller or spray gun. For best results lightly sand between coats.

Do not use when air or surface temperature is below 10°C or above 30°C

AEROSOL: Approximately 2m² per can.

BRUSH ON: Approximately 14m² per litre, depending on the nature of the surface.

AEROSOL:  Touch dry in 6-8 hours. Re-coat after 16 hours.

BRUSH ON: Touch dry in 4-6 hours. Re-coat after 16 hours.

Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied.

AEROSOL: To prevent nozzle blocking, after use turn can upside down and press button until only gas escapes.

Overspray can be removed while still wet with White Knight Rust Guard Solvent or mineral turps.

BRUSH ON: Clean brushes and equipment with White Knight Rust Guard Solvent or mineral turps immediately after use.