White Knight® Pot Belly Black

300g, 500ml

White Knight Pot Belly Black is a heat resistant paint designed for use on metal surfaces which are subject to radiant heat.



Features

• Heat resistant to 300°C

• Durable low sheen finish

• Self priming

• Excellent coverage

• Adjustable spray nozzle

• Safe to spray – CFC and lead free

• Non-chroming formula

• Low sheen

White Knight® Pot Belly Black is ideal for use on pot belly stoves, heaters, ovens, BBQ surrounds and flues.

Not suitable for use on BBQ hot plates or food contact surfaces.

1. PREPARATION

AEROSOL:

  • Thoroughly clean the surface and ensure it is free from grease, oil, dirt, rust scale and other contaminants.
  • Thoroughly sand new metal. Lightly sand previously painted and glossy surfaces.
  • Remove loose rust and flaking paint with a wire brush, scraper or mechanical sander back to bare metal.
  • Wipe surface with mineral turps and allow to dry before painting.
  • Cover all necessary areas to protect from overspray.

BRUSH ON:

  • Thoroughly clean the surface and ensure it is free from grease, oil, dirt, rust scale and other contaminants.
  • Thoroughly sand new metal. Lightly sand previously painted and glossy surfaces.
  • Remove loose rust and flaking paint with a wire brush, scraper or mechanical sander back to bare metal.
  • Wipe surface with mineral turps and allow to dry before painting.

2. APPLICATION

AEROSOL:

BEFORE SPRAYING

  • Shake can vigorously for 1 minute to ensure colour uniformity. Shake can occasionally during use.
  • Remove the cap carefully. Avoid using sharp objects that may puncture the can.
  • Test spray on a small inconspicuous area to ensure surface compatibility and finish suitability.

SPRAYING

  • Select the nozzle setting: The To change the nozzle setting, turn the red section on the nozzle.
  • Hold the can upright approximately 25cm from the surface.
  • Press button firmly and spray several light coats with a smooth sweeping motion, overlapping each spray pass. To prevent paint from sagging, avoid spraying too close to the surface or applying a heavy coat.
  • Repeat if necessary.

BRUSH ON:

  • Stir thoroughly with a broad flat stirrer in a circular lifting motion for at least 5 minutes before use and continue to stir at regular intervals during application.
  • Apply 2 coats by brush.

Do not use when air or surface temperature is below 15°C or above 30°C or in excessive humidity.

3. COVERAGE

  • AEROSOL: Approximately 1.5m² per can, depending on the nature of the surface and amount of overspray.
  • BRUSH ON: Approximately 16m² per litre, depending on the nature of the surface.

4. DRYING

  • AEROSOL: Touch dry in 1 hour. Re-coat after 16 hours.
  • BRUSH ON:  Touch dry in 1 hour. Re-coat after 16 hours.
  • Drying will be slower in cold or humid conditions, in the absence of ventilation or where heavy film builds are applied. 

5. DRY CURE

  • Hard dry conditions are achieved when the coated article is gradually heated from cold to operating temperature.
  • Some odour may be evident during curing. It is suggested practice to re-coat the article after the winter period. This will allow the full curing to take place prior to the next winter without any heat application.

6. CLEAN UP

  • AEROSOL: Overspray can be removed while still wet with mineral turps.
  • To clean the nozzle after use and prevent blocking turn the can upside down and press button until only gas escapes.
  • BRUSH ON: Clean brushes and equipment with White Knight Rust Guard® Solvent or mineral turps.

7. SAFETY & FIRST AID

AEROSOL:

KEEP OUT OF REACH OF CHILDREN.

  • This product is highly flammable. Store and use away from heat and eliminate any source of ignition.
  • If swallowed, drink plenty of water and seek medical advice immediately. Do not induce vomiting.
  • If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention.
  • Avoid breathing vapour or mist.
  • Use only with adequate ventilation.
  • If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents or thinners.
  • Warning - Misuse by concentrating and inhaling contents can be harmful or fatal.

BRUSH ON:

KEEP OUT OF REACH OF CHILDREN.

  • This product is highly flammable. Store and use away from heat and eliminate any source of ignition.
  • If swallowed, drink plenty of water and seek medical advice immediately. Do not induce vomiting.
  • If in eyes, immediately flush with running water for at least 15 minutes. Seek immediate medical attention.
  • Avoid breathing vapour or mist.
  • Use only with adequate ventilation.
  • If on skin, remove contaminated clothing. Wash skin thoroughly with soap and water. Do not use solvents of thinners.

For 24 hour medical emergency response in Australia call 1800 883 254 and in New Zealand call 0800 000 096


Colour Range

Colours
Black
*Due to colour variations in all browser types, the displayed colour palettes are a representation only of the actual colour. This should not be used in deciding the colour range suitable for you application.

Need Help?

It’s as easy as selecting a project type and the material involved